Ashly FTX 2001 | Action Audio and Visual

Click Picture to Enlarge (+)

Specifications

Power Output
(Maximum Average Power, 0.1% THD, 1KHz)
Rated Per Channel, Both Channels Driven
2 ohms: 550 Watts RMS
4 ohm: 475 Watts RMS
8 ohm: 300 Watts RMS
Mono Bridged:
4 ohms: 1100 Watts RMS
8 ohm: 950 Watts RMS
(FTC Continuous Power, 0.1% THD, 20Hz - 20KHz)
Rated Per Channel, Both Channels Driven
Stereo (per channel):
4 ohm: 400 Watts RMS
8 ohm: 250 Watts RMS
Mono Bridged:
8 ohm: 800 Watts RMS
Total Harmonic Distortion:
8 ohm: .01% 1kHz
8 ohm: .05% 20Hz
8 ohm: .1% 20kHz
IM Distortion (SMPTE): <.017%, 8 ohm
IMD (IHF): <.05%, 8 ohms
Hum and Noise (20Hz - 20KHz unweighted): -105dB from full output
Damping Factor: >250, 8 ohm, <1kHz
Bandwidth: 100kHz
Slew Rate: 50 V/µS
Frequency Response: ±0.2dB 20Hz-20kHz
Rise Time: 2µS 10%-90%
Full Power Input Sensitivity: 1.7V
Power Requirement: 110-125VAC, 50-60Hz (240V
Available)
Dimensions: 19L x 5.25H x 16.5D
Shipping Weight: 46 lbs
Specification conditions are: 120VAC mains at 60Hz, 25° C

Day rate: $50.00

Overview:

The power amplifier, being of two channels, shall deliver a mini-mum power of 300 watts RMS per channel into 8 ohm loads and 475 watts RMS per channel into 4 ohm loads, or 550 watts per channel into 2 ohm loads with both channels operating. When switched into bridged-mono mode, the amplifier it shall deliver at least 600 watts into a 16 ohm load, and 950 watts RMS into an 8 ohm load. The amplifier shall be immune to damage from shorted, open, or mismatched loads. The amplifier shall have a gain of 29 dB +/- .2dB per channel and an input sensitivity of 1.7 Volts +/- 2% for full rated output. Frequency response shall be 20Hz to 20kHz +/- .2dB. It shall be stable into any load, including pure capacitors and inductors. Hum and noise shall be at least 105dB below full output and SMPTE intermodulation distortion shall be less than .01%. The amplifier shall have rear panel switching for parallel mono and bridging modes and rear mounted level controls. The inputs shall be of balanced bridging type with barrier strip, 1/4 phone jacks, and female XLR connectors. A three-color L.E.D type indicator shall be employed to show the power level of each channel and self contained forced air cooling shall be used.

Each channel shall have a PROTECT LED which indicates an open relay due to short-circuit, ultrasonic, DC, or turn-on delay. The power output devices shall be of the Lateral MOS-FET type.

The amplifier shall weigh 53lbs net and mount in a standard 19 inch rack using three spaces (5.25 high). The power requirement shall be 110-125VAC, 50-60-Hz. The power amplifier shall be an Ashly FTX-2001.

Features:
Turn-on Delay
Fuseless Short Circuit Protection
U.L. Listed
5-Year Worry-Free Warranty
MOS-FET Output Devices
Class-A Full Complementary
Front End
Modular Construction
XLR, 1/4″, and Barrier Strip
inputs
Stereo, Parallel Mono & Bridging
Modes
LED Level meters
Forced Air Cooling
Perfect Overload and Square
Wave Response
Stable Into Any Load
Self Protecting Under Virtually
All Conditions
Input Transformers Optionally
Available
PowerCard Input Option Read